To verify a molder's internal quality management systems, audit their documentation, process controls, and traceability records. This guide provides a step-by-step process for evaluating quality management review and supplier compliance check capabilities.
- Start with document review to confirm the molder follows their stated quality management system.
- Verify that raw material traceability connects from certificate of analysis to the finished part.
- Check that process parameters and statistical process control data match the production reality.
- Test the molder's response to a specific nonconformance or change request.
Why Document Review Comes First
A molder quality audit begins with paper, not floor walking. Before you step onto the production floor, request the quality manual, the controlled document list, and the process flow diagram. These documents define the system. If the manual describes a five-step approval process, but the floor shows only two, the system is not operating as designed.
Read the quality manual for gaps. Look for missing sections on calibration, corrective action, or supplier approval. Check the revision dates. A document last updated years ago suggests the system is static. Ask for the current version of the process flow diagram. It should show every step from receiving raw material to final shipment, including hold points where quality inspection occurs.
Start with the quality manual’s structure. Most successful systems use a hierarchical approach. The top level defines policy and responsibilities. The next level breaks down procedures for specific functions like incoming inspection, machine setup, and final release. The lowest level contains work instructions, forms, and logbooks. If the manual skips a level, such as jumping directly from policy to “check parts,” the organization lacks defined accountability.
Check the document control system. Every controlled document should have a unique number, a revision level, and an effective date. Look for the controlled document register. It lists every active document and its location. If a form is found in a drawer with no control number, the molder is operating outside their own system. This often happens when operators use handwritten notes instead of the official log.
Review the process flow diagram carefully. It should be a linear or branching map of the production cycle. Identify the control points. For example, after resin receiving, there should be a hold point for verification. After mold setup, there should be a hold point for first article inspection. If the diagram shows a direct path from resin receiving to injection molding without a verification step, the molder is skipping a critical control. Ask if the diagram matches the physical layout. If the diagram shows a quality lab next to the molding floor, but the lab is in a different building, the process is not as described.
How to Verify Raw Material Traceability
The next step is to trace a batch of material through the system. Pick a lot number from a recent production run. Walk the chain backward. Find the certificate of analysis from the resin supplier. Check the receiving log to see when it arrived. Confirm the bin location and the date code on the bag or pellet container.
This supplier compliance check identifies whether the molder actually controls material inputs. A molder that mixes lots, stores materials for extended periods, or does not verify incoming resin specifications creates a risk. Ask for the material balance sheet. It should show how much material was used, how much was returned to the supplier, and how much was reworked.
Start with a specific part number. Find the production record for a recent run. Note the resin lot number used. Go to the receiving area. Pull the receiving log for that date. Match the lot number to the receiving entry. The entry should include the supplier name, the date of arrival, and the quantity received. If the log is missing or the lot number is not recorded, the chain is broken.
Go to the material storage area. Locate the bin or pallet for that lot. The container should have a label with the supplier name, the grade, the lot number, and the date code. Check the label against the certificate of analysis. The lot number on the label must match the one on the COA. If the label is faded or missing, the molder cannot prove the material’s identity.
Check for segregation. Resin lots should be segregated by supplier and grade. If a molder stores multiple grades in the same bin, or if they mix old and new lots, the traceability is compromised. Ask about the first-in, first-out policy. Most systems use FIFO to prevent material from sitting in storage too long. If the molder stores material for months or years, ask about the storage conditions. Humidity and heat can degrade resin properties, leading to part defects even if the original material was good.
Review the material balance sheet. It is a record of material usage. For a specific production run, the sheet should show the amount of resin loaded into the hopper, the amount of scrap generated, and the amount of rework. If the rework is high, the process may be unstable. If the molder sells scrap to the supplier, the balance sheet must reflect that. A missing balance sheet suggests the molder is not tracking material consumption accurately, which can hide waste or theft.
What to Look for in Process Controls
Move to the injection molding machines. The goal here is to verify that the process is controlled and repeatable. Check the machine logs. Do they show the actual cycle times, pressures, and temperatures? Compare these logs to the process window defined in the drawing or specification.
If the molder uses statistical process control, review the control charts. Are the X-bar and R charts trending? Are there any points outside the control limits? A molder that hits Cpk targets but shows no control chart data may be manipulating the numbers. Look for the actual sensor data, not just a summary report.
Check the tooling records. The mold number should match the part number. The cavity map should show which cavities are used. If the molder runs multiple cavities, verify that each is producing parts within tolerance. A single bad cavity can ruin a batch if the molder does not monitor it.
Inspect the machine setup sheet. It should list the target parameters for the specific part. For a plastic housing, the targets might include injection pressure, mold temperature, and cooling time. Compare these targets to the actual values in the machine log. If the log shows a pressure of 150 bar but the setup sheet says 180 bar, the process is not controlled. Ask why the deviation occurred. Was it a setup error? A machine problem? If the molder cannot explain the deviation, the process is unstable.
Review the control charts. They should be plotted for critical dimensions. For example, a control chart for a hole diameter should show the mean and range for each subgroup. Look for patterns. Points trending upward or downward, or points alternating above and below the mean, indicate a shift in the process. If the molder has points outside the control limits, ask for the nonconformance report associated with that time. If there is no report, the molder is ignoring the signal.
Check the tooling records. The mold number is unique to the tool. It should be stamped on the mold and recorded in the tooling database. The cavity map shows the location of each cavity. For a four-cavity mold, the map should show cavities 1, 2, 3, and 4. If the molder only uses cavities 1 and 2, the map should reflect that. If a cavity is out of tolerance, the molder should mark it as “out of service” or “under repair.” If a bad cavity is still running, parts from that cavity may be defective. Ask to see the dimensional data for each cavity. If the data is missing for one cavity, the molder is not monitoring it properly.
How to Evaluate Calibration and Measurement
The measurement system is the backbone of quality. Ask for the calibration certificates for the key gauges. The micrometers, the tensile testers, the dimensional checkers. Verify the calibration dates against the required interval. A micrometer calibrated once a year may be acceptable, but check the traceability to a national standard.
Walk the measurement area. Is it clean? Is the equipment protected from vibration and temperature swings? Ask the technician to measure a gauge block. Watch their technique. Do they use the correct force? Do they read the device correctly? A molder that relies on manual measurement without a documented procedure creates variability.
Start with the calibration log. It lists every gauge, its serial number, its last calibration date, and its next due date. Check if the next due date has passed. If a gauge is overdue, it is not trustworthy. Ask for the calibration certificate from the last service. It should state the tolerance of the gauge, the result of the check, and the date of calibration. The certificate should also show the accreditation of the calibration lab. If the lab is not accredited, the traceability may be weak.
Inspect the measurement area. It should be clean and organized. Gauges should be stored in cases or on dedicated stands. They should not be on the floor or in a drawer. Temperature control is critical. Most gauges require a stable temperature, often around 20 degrees Celsius. If the area is near a door or a window, temperature swings can affect measurements. Ask about the temperature log. If there is no log, the molder is not controlling the environment.
Watch a measurement being performed. Pick a gauge block and ask the technician to measure it. Watch their hands. Do they clean the gauge block before measuring? Do they use the correct force? For a micrometer, the force should be consistent. Too much force compresses the block. Too little force leads to a high reading. Do they read the scale correctly? Do they use the magnifier if available? If the technique is inconsistent, the measurements will vary. Ask for the measurement procedure. It should state the steps, the force to use, and the acceptance criteria. If there is no procedure, the molder is relying on individual skill, which is not repeatable.
Checking Corrective Action and CAPA
Nonconformance is inevitable. The quality of the molder shows in how they handle it. Pull a recent nonconformance report. Ask for the corrective and preventive action record. The root cause analysis should be specific. It should not say “operator error.” It should identify the mechanism. Did the material lot vary? Did the machine temperature drift? Did the tool wear?
Look for the effectiveness check. Did the molder verify that the fix worked? A CAPA without an effectiveness check is just a note. Ask for the list of customer complaints over the past year. For each, trace the action taken. If the same complaint repeats, the system is failing.
Pull a nonconformance report for a part that failed inspection. Read the description. It should state what failed, when it failed, and how many parts were affected. For example, “Part number 12345, lot A, 10 parts, failed dimensional check on feature B.” The root cause analysis should be specific. “Operator error” is not a root cause. It is a symptom. The root cause might be “The setup sheet was not updated after the mold change, leading to incorrect injection pressure.” Or it might be “The resin lot had higher moisture content, causing bubbles in the part.”
Review the corrective action. It should be specific and verifiable. “Retrain operators” is vague. “Update the setup sheet and verify it with a supervisor before starting production” is specific. Ask for the preventive action. It should prevent the same issue from happening elsewhere. For example, if one machine had a setup error, check if the same error could happen on other machines. If not, the system is not robust.
Check the effectiveness check. After the action is implemented, the molder should verify that it worked. For example, after fixing a setup error, they should run a new lot and inspect it. If the new lot passes, the fix worked. If it fails, the root cause was wrong. Ask for the record of this check. If there is no record, the molder is not closing the loop. They are just documenting the action, not the result.
Review customer complaints. Ask for a list of complaints over the past year. For each complaint, trace the CAPA. If the same complaint repeats, the system is failing. For example, if a customer complains about flash on a part, and the molder fixes the mold, but the customer complains again six months later, the fix did not work. Ask why the complaint recurred. Was the root cause wrong? Was the preventive action missing?
How to Test Supplier Compliance During the Audit
A supplier compliance check extends beyond paper. Ask the molder for their approved supplier list. Check if the resin suppliers are qualified. Do the molders have their own resin testing capability, or do they rely entirely on the supplier’s certificate of analysis? A molder that tests incoming resin has a stronger system.
Ask about the change management process. If the molder switches to a new resin grade, do they requalify the process? Do they notify the customer? A molder that makes changes without approval creates a major risk. Test this by asking for the last change request. How long did it take to approve? What documentation was created?
Start with the approved supplier list. It should list every supplier for critical materials, such as resin, mold steel, and lubricants. Check if the suppliers are qualified. The list should include the qualification date, the qualification criteria, and the approval status. If a supplier is listed as “approved,” ask for the qualification record. It should show the test results or the audit report. If the molder relies only on the supplier’s certificate of analysis, they are not verifying the material themselves. Ask if they have a resin testing capability. They should be able to test for moisture content, melt flow rate, and density. If they do not, they are accepting the supplier’s word.
Review the change management process. If the molder switches to a new resin grade, they must requalify the process. The new resin may have different flow properties, affecting the part dimensions. Ask for the last change request. It should state the reason for the change, the new material, and the approval status. Check the approval time. If it was approved in one day, the molder may be skipping steps. Ask for the documentation. It should include the test results, the process window update, and the customer notification. If the molder made the change without approval, it is a major finding. It shows they are not controlling changes to the process.
Common Mistakes in a Molder Quality Audit
Many audits fail because the auditor stays too high-level. Do not just read the quality manual. Check the floor. Do not just look at the Cpk report. Look at the raw data. Do not just ask if they have traceability. Pick a lot number and walk the chain.
Another mistake is focusing only on the production floor. The quality system includes purchasing, logistics, and IT. If the molder cannot find a material batch record because the ERP system is down, the traceability is broken. If the purchasing team buys materials from an unapproved supplier, the quality system is compromised.
Avoid the trap of “document theater.” Many molders have perfect documents but poor execution. The quality manual may be thick and detailed, but the floor may be chaotic. Check the floor. Look at the machines. Are they set up correctly? Are the parts being inspected? If the documents say “inspect every 10 parts,” but the floor shows no inspection records, the system is not working.
Avoid focusing only on production. The quality system is a chain. If purchasing buys the wrong resin, production gets the wrong material. If logistics ships the wrong part, the customer gets the wrong part. If IT is down, the records are lost. Check the purchasing area. Are they buying from approved suppliers? Check the logistics area. Are they verifying the part number before shipping? Check the IT system. Are the records accessible? If the ERP system is down, ask how they handle traceability. If they use paper backups, are they controlled? If not, the traceability is broken.
Final Verification Step
End the audit with a live test. Ask the molder to pull a part from a recent run. Verify the part number, the date code, and the cavity number. Check the inspection record. Confirm the part meets specification. This final step confirms that the system works in real time. It is not just theory. It is the daily reality of the molder’s operation.
Pick a part from a recent production run. It should be on the floor or in the finished goods area. Ask the molder to pull it out. Check the label. It should have the part number, the date code, and the cavity number. Compare the label to the production record. They should match. Check the inspection record. It should show the part passed inspection. Verify the part meets specification. Use a gauge to check a critical dimension. If the part fails, the system is not working. If it passes, the system is working.
This live test is the final proof. It shows that the documents, the process, and the execution are aligned. It is the real test of the molder’s quality system. If it fails, the audit has a major finding. If it passes, the audit can be closed with confidence.
Audit Checklist Table
| Audit Area | Key Document | Verification Method |
|---|---|---|
| Raw Material | Certificate of Analysis | Trace lot number to receiving log |
| Process Control | Control Charts | Inspect X-bar and R charts for limits |
| Measurement | Calibration Records | Verify traceability to national standard |
| Corrective Action | CAPA Log | Check root cause and effectiveness |
| Supplier Approval | Approved Supplier List | Confirm resin supplier qualification |
| Change Management | Change Request Form | Review approval time and documentation |
What to Do Next
After the molder quality audit, write a report. List the findings. Categorize them as major, minor, or observation. A major finding is a break in the quality system. It requires immediate action. A minor finding is a gap in documentation or a small process deviation. It requires a plan for correction.
Share the report with the molder. Give them a deadline to respond. For major findings, require a corrective action plan. For minor findings, require a plan to close the gap. Follow up. Do not close the audit until the molder has implemented the fixes and you have verified them. This step ensures that the audit changes the system, not just documents it.
Write the report while the details are fresh. List each finding with a clear description. Include the evidence. For example, “The receiving log for lot A was missing the date of arrival.” This specific evidence makes the finding undeniable. Categorize the findings. A major finding is a break in the quality system. For example, “The molder is using unapproved resin.” This requires immediate action. It must be stopped. A minor finding is a gap in documentation. For example, “The calibration certificate for the micrometer is missing.” This requires a plan for correction. It must be fixed. An observation is a suggestion for improvement. For example, “The measurement area is cluttered.” This is not a failure, but it can be improved.
Share the report with the molder. Give them a deadline to respond. For major findings, require a corrective action plan. The plan should state the root cause, the action, the owner, and the deadline. For minor findings, require a plan to close the gap. The plan should state the action, the owner, and the deadline. Follow up. Do not close the audit until the molder has implemented the fixes and you have verified them. If the molder does not respond by the deadline, escalate the issue. If they cannot fix the major finding, consider ending the business relationship.
How to Handle a Molder That Fails
If the molder fails the audit, decide the next step. Do not automatically fire them. Many molders have gaps they do not know about. Give them a clear path to improve. Set a target date. Re-audit in 30 or 60 days.
If they cannot fix the issues, consider moving to another molder. But do not move without a backup plan. A molder quality audit is not a one-time event. It is a relationship management tool. A molder that passes the audit today may slip tomorrow. Re-audit annually or when the process changes.
If the molder fails the audit, do not panic. A failed audit is not the end. It is a signal. Many molders have gaps they do not know about. They may have good intentions but poor execution. Give them a clear path to improve. Set a target date. For example, “Fix the traceability issue within 30 days.” Be specific about the requirements. Tell them exactly what needs to be fixed. Provide support if needed. For example, offer to help them update the receiving log. This shows you are a partner, not just a customer.
Set a target date. Re-audit in 30 or 60 days. The re-audit should focus on the failed items. Verify that the fixes are implemented. Check the evidence. For example, if the traceability was the issue, walk the chain again. If the fix worked, close the finding. If it did not, escalate the issue.
If they cannot fix the issues, consider moving to another molder. But do not move without a backup plan. Identify a new molder. Qualify them. Run a pilot. Do not stop the current molder until the new one is ready. A molder quality audit is not a one-time event. It is a relationship management tool. A molder that passes the audit today may slip tomorrow. Re-audit annually or when the process changes. Keep the molder accountable. Regular audits ensure the system stays strong.
Frequently asked questions
How often should I perform a molder quality audit?
Perform a full audit annually or when the process, product, or supplier changes. Spot checks can happen more frequently.
What is the difference between a major and minor finding?
A major finding is a break in the quality system that affects product conformance. A minor finding is a gap in documentation or a small process deviation.
Do I need to walk the production floor?
Yes. Document review alone does not confirm the system is operating. You must verify that floor practices match the written procedures.
How do I verify statistical process control data?
Ask for the raw sensor data, not just a summary. Check that the control charts are current and that points are within limits.
What if the molder does not have a quality manual?
This is a major finding. A molder without a defined quality management system cannot guarantee consistent quality. Require them to develop one.



