This audit checklist guides buyers through verifying nylon moisture content before production. It covers drying protocols, testing methods, and red flags for polyamide and high-glass nylon to ensure consistent part quality.
- Verify moisture levels with a dedicated meter before every production shift, not just at the start of a batch.
- Inspect drying logs for consistent temperature and cycle times, as these directly impact final pellet moisture.
- Watch for splay marks, short shots, and discoloration as visual indicators of insufficient drying or rehydration.
- Store dried nylon in sealed containers with desiccant to maintain low moisture levels until the machine is ready.
- Recheck moisture after any machine downtime or extended idle periods to catch reabsorbed water.
Why Moisture Verification Matters Before Production
Water is the most common cause of defect spikes in nylon production. Polyamide resins absorb moisture from ambient air, and that water migrates into the polymer during molding. The result is a predictable set of defects: splay marks, short shots, poor surface finish, and inconsistent mechanical properties. This checklist ensures you verify moisture content before every production run, catching issues before they become scrap.
Section 1: Drying Protocol Verification
Start by auditing the drying process itself. A verification step is only as good as the drying that preceded it.
- Confirm the drying temperature matches the resin datasheet recommendation for the specific grade. For standard nylon 6 and 6/6, typical drying temperatures fall in a specific range. High-glass nylon often requires lower temperatures to avoid degrading the glass filler.
- Check that the drying cycle time is sufficient. A standard batch may require several hours. Do not shorten the cycle to meet a production schedule.
- Inspect the dryer. Look for clogged filters, blocked air flow, or malfunctioning temperature sensors. A dryer that reads correctly but does not circulate air properly will produce inconsistent moisture levels.
- Review the drying log. Temperature and cycle time should be recorded for every batch. Missing entries are a red flag.
Red flags:
- Drying temperature set above the resin maximum.
- Cycle time significantly shorter than the recommended range.
- No log records for the current batch.
- Dried pellets stored in open containers.
Section 2: Moisture Content Testing
Drying logs are a record of the process. They are not a measure of the result. You must test the actual moisture content of the pellets before they enter the molding machine.
- Use a calibrated moisture meter. A standard benchtop meter is sufficient for most facilities.
- Sample from multiple points in the batch. Do not take a single sample from the top of a bag. Draw samples from the top, middle, and bottom of the dryer output.
- Test at the start of the shift and after any machine downtime. Nylon reabsorbs moisture quickly when the machine is stopped.
- Record the actual moisture reading. Compare it to the target range specified by the resin supplier.
Red flags:
- Moisture meter readings that drift over time without calibration.
- Sample taken from a single location only.
- No record of moisture testing after machine downtime.
- Moisture reading above the supplier specified maximum.
Section 3: Material Handling and Storage
Dry nylon is not a commodity. It is a hygroscopic material that will regain moisture if not handled correctly.
- Store dried pellets in sealed containers. Use containers with airtight seals, not open bins.
- Include desiccant in all storage containers. Replace desiccant regularly. A saturated desiccant pack provides no protection.
- Minimize time between drying and processing. The shorter the gap, the lower the risk of rehydration.
- Use dedicated transfer lines or bags for moisture-sensitive resins. Do not share equipment with resins that require different handling.
Red flags:
- Dried pellets stored in open bins.
- Desiccant packs missing or visibly damp.
- Long idle periods between drying and injection.
- Shared equipment without proper flushing.
Section 4: Machine-Side Verification
The molding machine itself can introduce moisture. Even if the pellets are dry, the hopper and barrel can absorb water.
- Check the hopper seal. A worn or missing gasket allows ambient air to enter the hopper during operation.
- Inspect the barrel for condensation. Condensation on the inside of the barrel indicates that the barrel is not hot enough to keep moisture from condensing.
- Verify that the machine has been heated to temperature before the first shot. Do not run cold shots to warm up the machine.
- Check for any water leaks near the machine. Even a slow drip near the hopper can add moisture over time.
Red flags:
- Visible condensation on the inside of the barrel.
- Hopper seal damaged or missing.
- Running cold shots to warm the machine.
- Water leaks near the hopper or material path.
Section 5: Visual and Process Defect Monitoring
Moisture issues do not always show up in the meter reading. They often appear in the part first.
- Inspect the first parts of every shift. Look for splay marks on the parting line, short shots, or a rough surface finish.
- Monitor the injection pressure. A sudden drop in pressure can indicate moisture in the barrel.
- Check the melt temperature. A lower-than-expected melt temperature can be a sign of moisture absorption.
- Compare part dimensions to the drawing. Moisture can cause shrinkage variations that affect critical dimensions.
Red flags:
- Splay marks appearing on new molds.
- Short shots on molds that ran well yesterday.
- Sudden changes in injection pressure or melt temperature.
- Dimensional drift on critical features.
Section 6: Documentation and Continuous Improvement
Verification is a process, not a one-time event. Documentation creates accountability and a baseline for improvement.
- Maintain a standard operating procedure for moisture verification. The procedure should cover testing, storage, and machine checks.
- Train all operators on the red flags. An operator who recognizes splay marks early can stop a run before it becomes a problem.
- Track moisture readings over time. Trends can reveal issues with the dryer, the storage environment, or the resin batch.
- Review failure data regularly. If splay marks or short shots are recurring, revisit the drying protocol and storage practices.
Red flags:
- No written procedure for moisture verification.
- No operator training on defect recognition.
- No trend data on moisture readings.
- No review of failure data after defect spikes.
Quick Reference: Moisture Verification Checklist
| Check Item | Frequency | Pass Criteria |
|---|---|---|
| Drying temperature | Per batch | Matches resin datasheet |
| Drying cycle time | Per batch | Meets or exceeds minimum |
| Moisture meter calibration | Weekly | Within manufacturer tolerance |
| Pellet moisture test | Per shift | Below supplier maximum |
| Hopper seal condition | Per shift | No visible damage |
| Barrel condensation | Per shift | None visible |
| Storage container seal | Per shift | Airtight and intact |
| Desiccant condition | Weekly | Not saturated |
Final Audit Note
A moisture verification program fails when it becomes a formality. The value is in catching the problem before the part is molded. If you are seeing splay marks, short shots, or inconsistent surface finish, stop and test the moisture before you adjust the process settings. The root cause is almost always water. Fix the water, and the process will stabilize.
Frequently asked questions
How often should I test nylon moisture content?
Test at the start of every production shift and after any machine downtime. Re-test if you observe defects like splay marks or short shots.
What is the typical moisture content for dry nylon?
Most suppliers recommend a maximum moisture level for production. Check the specific datasheet for your grade, as high-glass nylon may have different limits.
Can I use a standard moisture meter for high-glass nylon?
Yes, a standard benchtop moisture meter is suitable. Ensure it is calibrated for the correct material type and follow the supplier recommended testing protocol.
What are the most common visual signs of excessive moisture in nylon parts?
Splay marks on the parting line, short shots, rough surface finish, and visible bubbles or voids are the most common indicators of moisture issues.
How long can dried nylon remain in storage?
Dried nylon should be processed as soon as possible. If storage is necessary, use airtight containers with desiccant. Re-test moisture before production after any extended storage period.



